View DEVICE_8587750.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

? semiconductor components industries, llc, 2011 june, 2011 ? rev. 2 1 publication order number: ncp694/d ncp694 1a cmos low-dropout voltage regulator the ncp694 series of fixed output super low dropout linear regulators are designed for portable battery powered applications with high output current requirement up to 1 a and ? 3 mv typical load regulation at 1 a. each DEVICE contains a voltage reference unit, an error amplifier, a pmos power transistor, resistors for setting output voltage, a current limit circuits for overcurrent and thermal ? shutdown. a standby mode with ultra low supply current can be realized with the chip enable function. the DEVICE is housed in the sot ? 89 ? 5 and hson ? 6 packages. standard voltage versions are 0.8 v, 1.0 v, 1.2 v, 2.5 v, 3.3 v for fixed version and adjustable output voltage down to 1.0 v. features ? maximum operating voltage of 6.0 v ? minimum output voltage down to 0.8 v for fix version and 1.0 v for adjustable version ? load regulation ? 3 mv at 1 a output current ? low dropout ? build ? in auto discharge function for d version ? standby mode with low consumption ? these are pb ? free DEVICEs typical applications ? battery powered instruments ? hand ? held instruments ? camcorders and cameras ? portable communication equipments sot ? 89 ? 5 case 528ab see detailed ordering and shipping information in the package dimensions section on page 15 of this data sheet. ordering information marking diagrams http://onsemi.com xxx xmm xxxx = specific DEVICE code mm, yy = lot number g or = pb ? free package 1 1 6 1 6 xxx xyy hson ? 6 case 506ae for actual marking pb ? free indicator, ?g? or micro- dot ? ? may or may not be provided.
ncp694 http://onsemi.com 2 figure 1. pin description 123 321 4 545 123 654 321 456 (top view) (bottom view) (top view) (bottom view) sot ? 89 ? 5 hson ? 6 pin function description for sot ? 89 ? 5 package pin no. pin name description 1 adj/nc adjust pin for ncp694dadjht1g and ncp694hadjht1g / no connection 2 gnd power supply ground 3 ce this input is used to place the DEVICE into low ? power standby. when this input is pulled low, the DEVICE is disabled. if this function is not used, enable should be connected to v in . 4 v in positive power supply input voltage. 5 v out regulated output voltage. pin function description for hson ? 6 package pin no. pin name description 1 v out regulated output voltage 2 v out regulated output voltage 3 adj / nc adjust pin for ncp694dsanadjt1g and ncp694hsanadjt1g / no connection 4 gnd power supply ground 5 ce this input is used to place the DEVICE into low power standby. when this input is pulled low, the DEVICE is disabled. if this function is not used, enable should be connected to vin. 6 v in positive power supply input voltage current limit& thermal shutdown vin gnd vref vin ce vout vout current limit& thermal shutdown vin gnd vref vin ce vout vout version h (ncp694hxxxxt1g) figure 2. internal block diagram version d (ncp694dxxxxt1g)
ncp694 http://onsemi.com 3 maximum ratings rating symbol value unit input voltage v in 6.5 v enable voltage v ce ? 0.3 to v in v output voltage v out ? 0.3 to v in + 0.3 v power dissipation sot ? 89 ? 5 p d 900 mw power dissipation hson ? 6 p d 900 mw operating junction temperature t j +150 c operating ambient temperature t a ? 40 to +85 c storage temperature t stg ? 55 to +125 c stresses exceeding maximum ratings may damage the DEVICE. maximum ratings are stress ratings only. functional operation above t he recommended operating conditions is not implied. extended exposure to stresses above the recommended operating conditions may af fect DEVICE reliability. 1. this DEVICE series contains esd protection and exceeds the following tests: human body model 2000 v per jedec machine model method 200 v thermal characteristics rating symbol test conditions typical value unit junction ? to ? ambient sot ? 89 ? 5 r ja 1 oz copper thickness, 100 mm 2 111 c/w power dissipation sot ? 89 ? 5 p d 900 mw junction ? to ? ambient hson ? 6 r ja 1 oz copper thickness, 100 mm 2 111 c/w power dissipation hson ? 6 p d 900 mw note: single component mounted on an 80 x 80 x 1.5 mm fr4 pcb with stated copper head spreading area. using the following boundary conditions as stated in eia/jesd 51 ? 1, 2, 3, 7, 12.
ncp694 http://onsemi.com 4 electrical characteristics for fix version (v in = v out(nom.) + 1.0 v, v ce = v in , c in = 4.7 f, c out = 4.7 f, t a = 25 c, unless otherwise noted) characteristic symbol min typ max unit output voltage (t a = 25 c, i out = 100 ma, v in ? v out = 1 v) 0.8 v 1.0 v 1.2 v 2.5 v 3.3 v v out 0.770 0.970 1.170 2.450 3.234 0.8 1.0 1.2 2.5 3.3 0.830 1.030 1.030 2.550 3.366 v output current (v in ? v out = 1 v) i out 1 a input voltage v in 1.4 6.0 v line regulation (i out = 100 ma) reg line ? 0.05 0.2 %/v load regulation (i out = 1 ma to 300 ma, v in = v out + 2.0 v) reg load03 ? 15 ? 2 15 mv load regulation (i out = 1 ma to 1 a, v in = v out + 2.0 v) reg load1 ? ? 3 ? mv supply current (i out = 0 a, (v in ? v out ) = 1 v, v ce = v in ) i ss 60 100 a standby current (v ce = 0v, v in = 6.0 v) i stby 0.1 1.0 a short current limit (v out = 0 v) i sh 250 ma output voltage temperature coefficient t c ? 100 ? ppm/ c enable input threshold voltage (voltage increasing, output turns on, logic high) (voltage decreasing, output turns off, logic low) v thce 1.0 0 ? ? 6 0.4 v enable pull ? down current 100 220 na drop output voltage (t a = 25 c, i out = 300 ma) 0.8 v output voltage v out (v) 1.0 v 1.2 v 2.5 v 3.3 v v in ? v out 0.33 0.22 0.18 0.10 0.05 0.570 0.470 0.320 0.150 0.100 v drop output voltage (t a = 25 c, i out = 1a) 0.8 v output voltage v out (v) 1.0 v 1.2 v 2.5 v 3.3 v v in ? v out 0.72 0.64 0.56 0.32 0.18 v ripple rejection (ripple 200 mv pp , i out =100 ma, f = 1 khz) psrr 70 db output noise (bw = 10 hz to 100 khz, i out = 1 ma) v noise 30 v rms thermal shutdown temperature/hysteresis t shd /hyst 150/30 c r ds(on) of additional output transistor (d version only) r ds(on) 30 2. maximum package power dissipation limits must be observed. 3. low duty cycle pulse techniques are used during testing to maintain the junction temperature as close to ambient as possible.
ncp694 http://onsemi.com 5 electrical characteristic for adjustable version (v in = v out + 1 v, v ce = v in , c in = c out = 4.7 f, t a = 25 c, unless otherwise noted) characteristic symbol min typ max unit input voltage v in 1.4 6 v supply current (v out = v adj , v in = 2 v, v ce = v in ) i ss 60 100 ua standby current (v in = 6.0 v, v ce = 0 v) i standby 0.1 1 ua reference voltage for adjustable voltage regulator (v out = v adj , v in = 2.0 v, i out = 100 ma v ref 0.97 1 1.03 v output voltage range vout range 1 v in v output current (v out = v adj , v in = 2.0 v) i out 1 a load regulation (v in = 1.4 v, 1 ma < i out < 300 ma, v out = v adj ) v out /i out ? 15 ? 2 15 mv load regulation (v in = 1.7 v, 1 ma < i out < 1 a, v out = v adj ) v out /i out ? 3 mv dropout voltage (v out = v adj , i out = 300 ma) v drop300 0.18 0.32 v dropout voltage (v out = v adj , i out = 1 a) v drop1 0.56 v line regulation (v out = v adj , i out = 100 ma, 1.5 v < v in < 6.0 v v out /v in 0.05 0.2 %v psrr ( f = 1 khz, v out = v adj , v in = 2.5 v, i out = 100 ma, input ripple 0.5 v pp ) psrr 70 db output voltage temperature coefficient (i out = 100 ma, ? 40 c < t j < 85 c) v out /t j 100 ppm/ c short current limit (v out = v adj = 0) i lim 250 ma enable pull ? down current i ce 100 220 na enable input threshold voltage (voltage increasing, output turns on, logic high) (voltage decreasing, output turns off, logic low) vth ce 1 0 ? ? 6 0.4 v thermal shutdown temperature/hysteresis t shdn / hyst 150/ 30 c r ds(on) of additional output transistor (d version only) r ds(on) 30
ncp694 http://onsemi.com 6 applications information a typical application circuit for the ncp694 series is shown in figure 5, typical application schematic. input decoupling (c1) a 4.7 f capacitor either ceramic or tantalum is recommended and should be connected as close as possible to the pins of ncp694 DEVICE. higher values and lower esr will improve the overall line transient response. output decoupling (c2) the minimum decoupling value is 4.7 f and can be augmented to fulfill stringent load transient requirements. the regulator accepts ceramic chip capacitors as well as tantalum DEVICEs. if a tantalum capacitor is used, and its esr is large, the loop oscillation may result. because of this, select c2 carefully considering its frequency characteristics. larger values improve noise rejection and load regulation transient response. enable operation the enable pin ce will turn on or off the regulator. these limits of threshold are covered in the electrical specification section of this data sheet. if the enable is not used then the pin should be connected to v in . the d version DEVICEs (ncp694dxxxxt1g) have additional circuitry in order to reach the turn ? off speed faster than normal type. when the mode is into standby with ce signal, auto discharge transistor turns on. hints please be sure the v in and gnd lines are suf ficiently wide. if their impedance is high, noise pickup or unstable operation may result. set external components, especially the output capacitor, as close as possible to the circuit, and make leads as short as possible. thermal as power across the ncp694 increases, it might become necessary to provide some thermal relief. the maximum power dissipation supported by the DEVICE is dependent upon board design and layout. mounting pad configuration on the pcb, the board material, and also the ambient temperature effect the rate of temperature rise for the part. this is stating that when the ncp694 has good thermal conductivity through the pcb, the junction temperature will be relatively low with high power dissipation applications. output voltage setting of adjustable version. an external two resistors are required for setting desired output voltage as shows figure 3. output voltage setting. the equation for the output voltage is mentioned in equation below. v out v ref r1 i1 (eq. 1) v ref r1 i adj i2 v ref r1 v ref r adj r1 v ref r2 v ref 1 r1 r adj r1 r2 1.0 1 r1 r adj r1 r2 for better accuracy, choosing r2 << r adj reduces the error given by adj pin consumption. the typical resistance r adj is showed in figure 4. adj pin resistance figure 3. output voltage setting gnd adj r1 r2 i1 i2 vout radj vref = 1 v iadj 1.8 1.6 1.4 1.2 1.0 0.8 ? 50 ? 25 0 25 50 75 100 figure 4. adj pin resistance vs. temperature t j , temperature ( c) r adj , resistance (m )
ncp694 http://onsemi.com 7 figure 5. typical application schematic gnd vin vout nc vout ce gnd vout vin gnd 1 2 3 6 5 4 ncp694dsan08t1g 4.7 f c1 4.7 f c2
ncp694 http://onsemi.com 8 typical characteristics 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 output current (a) output voltage (v) figure 6. output voltage vs. output current v in = 1.4 v 1.6 v 2.0 v 2.5 v v out = 0.8 v t a = 25 c 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 output current (a) output voltage (v) figure 7. output voltage vs. output current v in = 3.5 v 2.5 v 1.7 v 3.0 v v out = 1.5 v t a = 25 c 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 v in = 4.0 v 4.5 v 3.6 v v out = 3.3 v t a = 25 c output current (a) output voltage (v) figure 8. output voltage vs. output current 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 v in = 1.4 v 1.6 v 2.5 v 2.0 v v out = v adj = 1.0 v t a = 25 c output voltage (v) output current (a) figure 9. output voltage vs. output current for adjustable output 0.0 0.2 0.4 0.6 0.8 1.0 1.2 0.0 1.0 2.0 3.0 4.0 5.0 6.0 input voltage (v) output voltage (v) figure 10. output voltage vs. input voltage i out = 1 ma 50 ma 100 ma 300 ma v out = 0.8 v t a = 25 c 0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 0.0 1.0 2.0 3.0 4.0 5.0 6.0 v out = 1.5 v t a = 25 c i out = 1 ma 50 ma 100 ma 300 ma input voltage (v) figure 11. output voltage vs. input voltage output voltage (v)
ncp694 http://onsemi.com 9 typical characteristics input voltage (v) output voltage (v) figure 12. output voltage vs. input voltage v out = 3.3 v t a = 25 c 3.5 3.0 2.5 2.0 1.5 1.0 0.5 0 0 1.0 2.0 3.0 4.0 5.0 6.0 i out = 1 ma 50 ma 100 ma 300 ma 0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 0123456 input voltage (v) figure 13. supply current vs. input voltage supply current ( a) v out = 0.8 v i out = 0 ma t a = 25 c 0.0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 0123456 input voltage (v) supply current ( a) figure 14. supply current vs. input voltage v out = 1.5 v i out = 0 ma t a = 25 c 0.0 10.0 20.0 30.0 40.0 50.0 60.0 70.0 0123456 supply current ( a) input voltage (v) figure 15. supply current vs. input voltage v out = 3.3 v i out = 0 ma t a = 25 c 0.780 0.785 0.790 0.795 0.800 0.805 0.810 0.815 0.820 ? 40.0 ? 20.0 0.0 20.0 40.0 60.0 80.0 temperature ( c) output voltage (v) figure 16. output voltage vs. temperature v out = 0.8 v i out = 0 ma 1.470 1.480 1.490 1.500 1.510 1.520 ? 40.0 ? 20.0 0.0 20.0 40.0 60.0 80.0 output voltage (v) temperature ( c) figure 17. output voltage vs. temperature v out = 1.5 v i out = 0 ma
ncp694 http://onsemi.com 10 typical characteristics 3.292 3.293 3.294 3.295 3.296 3.297 3.298 3.299 3.300 3.301 3.302 ? 40.0 ? 20.0 0.0 20.0 40.0 60.0 80.0 temperature ( c) output voltage (v) figure 18. output voltage vs. temperature v out = 3.3 v i out = 0 ma 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.0 0.2 0.4 0.6 0.8 1.0 v out = 0.8 v t a = 85 c 25 c ? 40 c output current (a) figure 19. dropout voltage vs. output current dropout voltage (v) 0 0.05 0.1 0.15 0.2 0.25 0.3 0.35 0.4 0 0.2 0.4 0.6 0.8 1 v out = 1.5 v output current (a) figure 20. dropout voltage vs. output current dropout voltage (v) ? 40 c 25 c t a = 85 c 0.00 0.02 0.04 0.06 0.08 0.10 0.12 0.14 0.16 0.18 0.20 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 dropout voltage (v) 25 c ? 40 c t a = 85 c output current (a) figure 21. dropout voltage vs. output current v out = 3.3 v 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.0 0.2 0.4 0.6 0.8 1.0 25 c ? 40 c t a = 85 c v out = v adj = 1 v output current (a) figure 22. dropout voltage vs. output current for adjustable output dropout voltage (v) 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 1 1.5 2 2.5 3 3.5 4 4.5 5 dropout voltage (v) set output voltage (v) figure 23. dropout voltage vs. set output voltage t a = 25 c i out = 1 a 500 ma 100 ma
ncp694 http://onsemi.com 11 typical characteristics 0 10 20 30 40 50 60 70 80 0.1 1.0 10.0 100 psrr (db) frequency (khz) figure 24. psrr vs. frequency v out = 0.8 v v in = 1.8 v + 0.5 v pp modulation t a = 25 c c out = 4.7 f i out = 1 a i out = 100 ma 0 10 20 30 40 50 60 70 80 90 0.1 1.0 10.0 100 i out = 100 ma i out = 1 a v out = 1.5 v v in = 2.5 v + 0.5 v pp modulation t a = 25 c c out = 4.7 f frequency (khz) figure 25. psrr vs. frequency psrr (db) 0 10 20 30 40 50 60 70 80 90 0.1 1.0 10.0 100 psrr (db) frequency (khz) figure 26. psrr vs. frequency v out = 3.3 v v in = 4.3 v + 0.5 v pp modulation t a = 25 c c out = 4.7 f i out = 1 a i out = 100 ma 0.0 0.5 1.0 1.5 2.0 2.5 3.0 ? 100 102030405060708090100 0.78 0.79 0.80 0.81 0.82 0.83 0.84 input voltage (v) time ( s) figure 27. line transient response output voltage (v) v out = 0.8 v v in = step 1.8 to 2.8 v t r = t f = 5 s c out = 4.7 f, i out = 100 ma t a = 25 c input voltage output voltage
ncp694 http://onsemi.com 12 typical characteristics input voltage (v) time ( s) figure 28. input transient response output voltage (v) input voltage output voltage 10 20 30 40 50 60 70 80 90 100 110 ? 100 102030405060708090100 0.78 0.79 0.80 0.81 0.82 0.83 0.84 0.85 0.86 0.87 0.88 output current (ma) time ( s) figure 29. load transient response output voltage (v) v out = 0.8 v v in = 1.8 v c out = 4.7 f, i out = step 50 ma to 100 ma t a = 25 c output voltage output current 10 20 30 40 50 60 70 80 90 100 110 ? 100 102030405060708090100 3.27 3.28 3.29 3.30 3.31 3.32 3.33 3.34 3.35 3.36 3.37 output current (ma) time ( s) figure 30. load transient response output voltage (v) v out = 3.3 v v in = 4.3 v c out = 4.7 f, i out = step 50 ma to 100 ma t a = 25 c output voltage output current 0.0 1.0 2.0 3.0 4.0 5.0 6.0 ? 100 102030405060708090100 3.290 3.295 3.300 3.305 3.310 3.315 3.320 v out = 3.3 v v in = step to 4.3 v to 5.3 v t r = tf = 5 s, c out = 4.7 f i out = 100 ma t a = 25 c
ncp694 http://onsemi.com 13 typical characteristics figure 31. output voltage vs. ce pin turn ? on ncp694dx08xx figure 32. output voltage vs. ce pin turn ? on ncp694dx33xx
ncp694 http://onsemi.com 14 typical characteristics figure 33. output voltage vs. ce pin turn ? off ncp694h08xxxx figure 34. output voltage vs. ce pin turn ? off ncp694d08xxxx
ncp694 http://onsemi.com 15 ordering information DEVICE nominal output voltage description marking package shipping ? ncp694hadjht1g adj. enable high l 0 0 b sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694h08ht1g 0.8 v enable high l 0 8 b sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694h10ht1g 1.0 v enable high l 1 0 b sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694h12ht1g 1.2 v enable high l 1 2 b sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694h25ht1g 2.5 v enable high l 2 5 b sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694h33ht1g 3.3 v enable high l 3 3 b sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694dadjht1g adj. enable high ? auto discharge l 0 0 d sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694d08ht1g 0.8 v enable high ? auto discharge l 0 8 d sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694d10ht1g 1.0 v enable high ? auto discharge l 1 0 d sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694d12ht1g 1.2 v enable high ? auto discharge l 1 2 d sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694d25ht1g 2.5v enable high ? auto discharge l 2 5 d sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694d33ht1g 3.3 v enable high ? auto discharge l 3 3 d sot ? 89 ? 5 (pb ? free) 1000 / tape & reel ncp694hsanadjt1g adj. enable high h 0 0 b hson ? 6 (pb ? free) 3000 / tape & reel ncp694hsan08t1g 0.8 v enable high h 0 8 b hson ? 6 (pb ? free) 3000 / tape & reel ncp694hsan10t1g 1.0 v enable high h 1 0 b hson ? 6 (pb ? free) 3000 / tape & reel ncp694hsan12t1g 1.2 v enable high h 1 2 b hson ? 6 (pb ? free) 3000 / tape & reel ncp694hsan25t1g 2.5 v enable high h 2 5 b hson ? 6 (pb ? free) 3000 / tape & reel ncp694hsan33t1g 3.3 v enable high h 3 3 b hson ? 6 (pb ? free) 3000 / tape & reel ncp694dsanadjt1g adj. enable high ? auto discharge h 0 0 d hson ? 6 (pb ? free) 3000 / tape & reel ncp694dsan08t1g 0.8 v enable high ? auto discharge h 0 8 d hson ? 6 (pb ? free) 3000 / tape & reel ncp694dsan10t1g 1.0 v enable high ? auto discharge h 1 0 d hson ? 6 (pb ? free) 3000 / tape & reel ncp694dsan12t1g 1.2 v enable high ? auto discharge h 1 2 d hson ? 6 (pb ? free) 3000 / tape & reel ncp694dsan25t1g 2.5 v enable high ? auto discharge h 2 5 d hson ? 6 (pb ? free) 3000 / tape & reel ncp694dsan33t1g 3.3 v enable high ? auto discharge h 3 3 d hson ? 6 (pb ? free) 3000 / tape & reel ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our tape and reel packaging specifications brochure, brd8011/d.
ncp694 http://onsemi.com 16 package dimensions sot ? 89, 5 lead case 528ab ? 01 issue o mounting footprint* recommended c 0.10 top view side view bottom view c h 1 dim min max millimeters a 1.40 1.60 b1 0.37 0.57 b 0.32 0.52 c 0.30 0.50 d 4.40 4.60 d2 1.40 1.80 e 2.40 2.60 notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. lead thickness includes lead finish. 4. dimensions d and e do not include mold flash, protrusions, or gate burrs. 5. dimensions l, l2, l3, l4, l5, and h are meas- ured at datum plane c. e 1.40 1.60 l 1.10 1.50 h 4.25 4.45 l2 0.80 1.20 l3 0.95 1.35 l4 0.65 1.05 l5 0.20 0.60 *for additional information on our pb ? free strategy and soldering details, please download the on semiconductor soldering and mounting techniques reference manual, solderrm/d. d e a c 23 54 l l5 e e b b1 l2 d2 l4 l3 2x 0.62 dimensions: millimeters 1 2x 1.50 1.30 2.79 0.45 1.50 1.65 4.65 4x 0.57 1.75 1
ncp694 http://onsemi.com 17 package dimensions hson ? 6 case 506ae ? 01 issue a 13 4 6 d a b e e1 0.20 c 0.20 c pin one reference 2 x 2 x top view notes: 1. dimensioning and tolerancing per asme y14.5m, 1994. 2. controlling dimension: millimeters. 3. dimension b applies to plated terminal and is measured between 0.10 and 0.15 mm from terminal. 4. coplanarity applies to the exposed pad as well as the terminals. b 6 x seating plane a (a3) l 6 x e c 0.08 c 6 x 0.10 c side view d2 4 6 3 1 0.10 c 0.05 c e2 a b bottom view note 3 dim min max millimeters a 0.70 0.90 a3 0.15 ref b 0.20 0.40 d 2.90 bsc d2 1.40 1.60 e 3.00 bsc e1 2.80 bsc e2 1.50 1.70 e 0.95 bsc l 0.15 0.25 exposed pad on semiconductor and are registered trademarks of semiconductor components industries, llc (scillc). scillc reserves the right to mak e changes without further notice to any products herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for an y particular purpose, nor does scillc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including wi thout limitation special, consequential or incidental damages. ?typical? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different application s and actual performance may vary over time. all operating parameters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the rights of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the scillc product could create a sit uation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemnify and hold scillc and its of ficers, employees, subsidiaries, af filiates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, direct ly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufacture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. publication ordering information n. american technical support : 800 ? 282 ? 9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81 ? 3 ? 5773 ? 3850 ncp694/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303 ? 675 ? 2175 or 800 ? 344 ? 3860 toll free usa/canada fax : 303 ? 675 ? 2176 or 800 ? 344 ? 3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your local sales representative

▲Up To Search▲

Price & Availability of DEVICE

	To Download DEVICE Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .